[PLUG] Resolved: Convert .wav to .mp3 in Slackware 14.2

[Dick Steffens]

On 2/25/19 9:44 PM, Ben Koenig wrote:
> lame is a build-time dependency of ffmpeg, so did you install lame 
> before you ran the ffmpeg.SlackBuild script?
>
> Also, the SBo script doesn't auto-detect these dependencies, since the 
> list is huge and it doesn't want to make licensing assumptions.
>
> See the SBo page for details, the list is as follows:
>
> ASS=yes|no (default: no), requires libass
> BLURAY=yes|no (default: no), requires libbluray
> BS2B=yes|no (default: no), requires libbs2b
> CELT=yes|no (default: no), requires celt
> CHROMAPRINT=yes|no (default: no), requires chromaprint
> DC1394=yes|no (default: no), requires libdc1394
> DECKLINK=yes|no (default: no), requires decklink-sdk
> EBUR128=yes|no (default: no), requires libebur128
> FDK_AAC=yes|no (default: no), requires libfdk-aac (creates 
> non-redistributable binary)
> FLITE=yes|no (default: no), requires flite
> FREI0R=yes|no (default: no), requires frei0r
> GME=yes|no (default: no), requires libgme
> GSM=yes|no (default: no), requires gsm
> IEC61883=yes|no (default: no), requires libiec61883 and libavc1394
> ILBC=yes|no (default: no), requires libilbc
> LADSPA=yes|no (default: no), requires ladspa_sdk
> LAME=yes|no (default: no), requires lame
> MODPLUG=yes|no (default: no), requires libmodplug
> NETCDF=yes|no (default: no), requires netcdf
> OPENAL=yes|no (default: no), requires OpenAL
> OPENCORE=yes|no (default: no), requires opencore-amr
> OPENCV=yes|no (default: no), requires opencv-legacy
> OPENSSL=yes|no (default: no), creates non-redistributable binary
> OPUS=yes|no (default: no), requires opus
> RTMP=yes|no (default: no), requires rtmpdump
> RUBBERBAND=yes|no (default: no), requires rubberband
> SCHROEDINGER=yes|no (default: no), requires schroedinger
> SNAPPY=yes|no (default: no), requires snappy
> SPEEX=yes|no (default: no), requires speex
> TESSERACT=yes|no (default: no), requires tesseract
> TWOLAME=yes|no (default: no), requires twolame
> VIDSTAB=yes|no (default: no), requires vid.stab
> WEBP=yes|no (default: no), requires libwebp
> X264=yes|no (default: no), requires x264
> X265=yes|no (default: no), requires x265
> XVID=yes|no (default: no), requires xvidcore
> ZMQ=yes|no (default: no), requires zeromq
> ZVBI=yes|no (default: no), requires zvbi
>
>
> As you can see, LAME needs to be enabled in order for support to be 
> built in. So you would install the LAME package, then build ffmpeg 
> with the following command:
>
> $ LAME=yes ffmpeg.SlackBuild

I didn't install Lame before installing ffmpeg. That makes sense that it 
needed to be there first. So if I just run the SlackBuild script for 
ffmpeg again, as you describe, then I should be able to get it working?

Thanks.

-- 
Regards,

Dick Steffens